Guide to Making a Fish Mouth

The Fish Mouth is named after the way one bamboo piece “bites” into its counterpart. This traditional joinery technique makes use of the bamboo’s intrinsic properties by evenly distributing loads across the full section of the bamboo culm.

The art of making this joint can be broken down into the following steps:

1. Gather The Right Materials:

  • Four pieces of treated dry bamboo, three have a larger diameter than the last one. For instance, with a Petung piece of 10 cm diameter, try to have a smaller piece of around 6 cm.
  • An electric drill, with bits of 3 to 4 mm diameter
  • A mutik (traditional bamboo carving knife), chosen according to your dominant hand (a)
  • A curved chisel (b)
  • A hammer (c)
  • A few wooden dowels (at least 10)
  • A pencil (d)
  • A ruler/tape measurer (e)
  • A hand saw (f)
  • Protective wear
Photo: The traditional tools needed to make a fish mouth. (©Bamboo U).

2. Prepare The Fish Mouth:

  • i. To add strength to the joint, the top of the mouth on the column should be cut close to a node (use the diameter as reference).
    Then, divide into four equal parts.
    Between the node and the end of the column, draw a line around the surface. The distance from the end of the column and the line should be the same as the radius of the beam.
  • ii. With your pencil, draw an approximate shape for your fish mouth.
    Hold the column and saw along the diagonals
  • iii. Then, carve out the mouth’s shape in upwards motions (working in the same direction as the bamboo fibers)

3. Make The Hole Joint:

  • i. Take the third, smaller piece of bamboo. It will act as the tie between the column and beam.
  • ii. Draw out its diameter on the beam, where the fish mouth will sit. Taking the chisel and the mutik, carve out the “hole”.
    Slot the piece in, it should fit in tight and all the way through to the opposite culm wall.
    Then, drill and dowel.
  • iii. Slip the column over the smaller bamboo piece to secure the fish mouth to the beam. Drill and dowel through the column and the small bamboo at opposite angles.
    In this form, the joint is commonly used for furniture design and smaller structures.

4. Make The Cross-Brace:

If used in construction, the joint should be strengthened by adding a cross-brace between the beam and column at 45° angles with both the column and the beam.

  • i. To achieve this, measure the same distance from the fish mouth to where the cross-brace will sit on both the column and beam.
  • ii. Measure the values of a and b (see drawing). They determine the depth of your cut. Saw accordingly.
  • iii. Using the mutik, carve out the right shape for the brace to sit on the beam or column.
  • iv. Secure it by drilling in dowels.

The art of joining bamboo together relies principally on a strong understanding of the material as well as a careful hand (or two). The fish mouth joint testifies to beautiful craftsmanship and strength. It is something we are privileged to be able to share here and during our courses.

About the author
Cécile Durand | Management Consulting Professional

After finishing her Masters of Architecture at the University of Hong Kong where she wrote her thesis about bamboo construction for the rural communities of Bali, she now forms part of the Bamboo U Team as a Management Consulting Professional.

Crafting a Curvilinear Bamboo Table

Last October 2023, Nathalie and Ahmed joined Bamboo U to learn about bamboo design and…

Building a Bamboo Meditation Bench

Last August 2023, Moni came from Canada and joined Bamboo U to immerse in the…

Bamboo U - Bamboo Umbrella by Harshita Sharma

Building a Bamboo Umbrella Lamp

Join me on a journey of conceptualization, contemplation, and the crafting process as I guide…

BAMBOO U - Vertical Soal Diffusion on Bamboo Pole Process (2)

DIY Bamboo Treatment: a Step-By-Step Guide

Learn the simple, budget-friendly Vertical Soak Diffusion method for durable, long-lasting bamboo treatment.